1. Scope
1.1 This specification defines the requirements for grading and quality of fine and coarse aggregate (other than lightweight or heavyweight aggregate) for use in concrete.
1.2 This specification is for use by a contractor, concrete supplier, or other purchaser as part of the purchase document describing the material to be furnished.
Note 1—This specification is regarded as adequate to ensure satisfactory materials for most concrete. It is recognized that, for certain work or in certain regions, it may be either more or less restrictive than needed. For example, where aesthetics are important, more restrictive limits may be considered regarding impurities that would stain the concrete surface. The specifier should ascertain that aggregates specified are or can be made available in the area of the work, with regard to grading, physical, or chemical properties, or combination thereof.
1.3 This specification is also for use in project specifications to define the quality of aggregate, the nominal maximum size of the aggregate, and other specific grading requirements. Those responsible for selecting the proportions for the concrete mixture shall have the responsibility of determining the proportions of fine and coarse aggregate and the addition of blending aggregate sizes if required or approved.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.
2. Referenced Documents
C1105 Test Method for Length Change of Concrete Due to Alkali-Carbonate Rock Reaction
C1157 Performance Specification for Hydraulic Cement
C117 Test Method for Materials Finer than 75-m (No. 200) Sieve in Mineral Aggregates by Washing
C123 Test Method for Lightweight Particles in Aggregate
C1240 Specification for Silica Fume Used in Cementitious Mixtures
C125 Terminology Relating to Concrete and Concrete Aggregates
C1260 Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method)
C1293 Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction
C131 Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine
C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates
C142 Test Method for Clay Lumps and Friable Particles in Aggregates
C150 Specification for Portland Cement
C1567 Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method)
C227 Test Method for Potential Alkali Reactivity of Cement-Aggregate Combinations (Mortar-Bar Method)
C289 Test Method for Potential Alkali-Silica Reactivity of Aggregates (Chemical Method)
C29/C29M Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate
C294 Descriptive Nomenclature for Constituents of Concrete Aggregates
C295 Guide for Petrographic Examination of Aggregates for Concrete
C311 Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete
C330 Specification for Lightweight Aggregates for Structural Concrete
C331 Specification for Lightweight Aggregates for Concrete Masonry Units
C332 Specification for Lightweight Aggregates for Insulating Concrete
C342 Test Method for Potential Volume Change of Cement-Aggregate Combinations
C40 Test Method for Organic Impurities in Fine Aggregates for Concrete
C441 Test Method for Effectiveness of Pozzolans or Ground Blast-Furnace Slag in Preventing Excessive Expansion of Concrete Due to the Alkali-Silica Reaction
C535 Test Method for Resistance to Degradation of Large-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine
C586 Test Method for Potential Alkali Reactivity of Carbonate Rocks as Concrete Aggregates (Rock-Cylinder Method)
C595 Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C637 Specification for Aggregates for Radiation-Shielding Concrete
C638 Descriptive Nomenclature of Constituents of Aggregates for Radiation-Shielding Concrete
C666/C666M Test Method for Resistance of Concrete to Rapid Freezing and Thawing
C87 Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar
C88 Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate
C989 Specification for Ground Granulated Blast-Furnace Slag for Use in Concrete and Mortars
D3665 Practice for Random Sampling of Construction Materials
D75 Practice for Sampling Aggregates
E11 Specification for Wire Cloth and Sieves for Testing Purposes
Index Terms
aggregates; coarse aggregate; concrete aggregates; fine aggregate; Aggregate--specifications; Coarse aggregate--specifications; Concrete aggregates--specifications; Fine aggregate
Citing ASTM Standards
[Back to Top]
